20ft Foldable Container House
Product Overview
The 20ft Foldable Container House is a modular building engineered for long-haul ocean freight and rapid deployment. Walls and roof fold inward on hinged connections, reducing the collapsed height to approximately 580mm - about one quarter of the deployed volume.
That compression is the whole point. A single high-cube container carries several times more units than conventional shipped-assembled boxes, which matters most where mobilisation speed and freight cost decide the project: emergency shelter, disaster relief, epidemic isolation facilities and remote site camps.
On site, one crane lifts and unfolds the box; wall panels slide into place and bolts are tightened. No on-site welding is required. Industry practice is one crane plus four workers completing a single unit in 3–10 minutes.
Core Advantages
Transport density
Collapsed height of approximately 580mm and volume reduced to roughly one quarter. Folded units are neither over-width nor over-height, so no over-width transport permit is required - inland and ocean legs are handled as standard container cargo.
01
Minutes, not days
Crane unfold plus bolt tightening, with no site welding. Suited to emergency response, post-disaster housing and isolation facilities where time is the binding constraint.
02
Structural integrity
Q235B cold-formed galvanised steel frame. Four welded corner castings positioned to ISO marine container standards serve as both transport locating points and certified lifting points. Electrostatic powder coating, film thickness ≥100μm.
03
Class A fire performance (rock wool option)
With rock wool core the panels achieve Class A non-combustible rating with fire resistance up to 70 minutes, meeting fire requirements commonly mandated in EU and Gulf projects.
04
Relocatable
Units fold and unfold repeatedly. At project end the whole box relocates to the next site; relocation cost for a single unit is comparatively low.
05
Technical Specifications
1. Dimensions & Area
|
Item |
Value |
|
Deployed dimensions (Z-type folding) |
5900 × 2438 × 2500 mm |
|
Collapsed height (hinged type) |
approx. 580 mm |
|
Volume compression ratio |
approx. 1/4 |
|
Usable area (hinged 20ft) |
approx. 15 m² |
|
Usable area (Z-type folding) |
approx. 14.4 m² |
|
Unit weight |
1.8–2.0t |
|
Units per 40HQ |
4 |
2. Structural System
|
Component |
Material / Specification |
|
Main frame (Z-type) |
Q235B cold-bent galvanised steel, 3.5mm wall |
|
General structural steel |
Q235 / Q235B / Q345, by member |
|
Folding hinge |
Q235 thickened galvanised hinge |
|
Corner castings |
4 welded corner casts, ISO marine container positioning |
|
Forklift pockets |
2 on long side; internal clearance 252×100mm; centre distance 2050mm (options: 950/1650mm or none) |
|
Surface coating |
Electrostatic powder coating, film thickness ≥100μm |
|
Roof purlins |
C-section galvanised tube, by span |
3. Envelope System
|
Item |
Value |
|
Core material options |
EPS / Glasswool / Rockwool / PU |
|
Common wall panel thickness |
50mm / 75mm |
|
Rock wool panel thickness range |
Tongue-and-groove 40–150mm; corrugated 50–150mm |
|
Rock wool effective width |
950mm / 1150mm |
|
Rock wool steel skin thickness |
0.4–0.8mm |
|
Rock wool core density |
120–150 kg/m³ |
|
Rock wool thermal conductivity |
≤0.043 W/(m·K) |
|
Rock wool fire resistance |
Up to 70 minutes |
|
Rock wool acoustic |
Rw 29–30dB; sound absorption ΔLA 15.7dB(A) |
|
Thermal load shrinkage temperature |
>600°C |
|
Rock wool minimum threshold |
GB/T 11835-1998: density ≥100kg/m³, bond strength ≥0.06MPa |
|
Roof panel (EPS build-up) |
75mm EPS + 0.30mm PPGI |
|
100mm rock wool upgrade |
U-value 0.38 W/(m²·K); EI120–EI240; 42dB; 12–15kg/m² |

Applications
|
Application |
Why foldable |
|
Emergency shelter / disaster relief |
Minute-scale deployment and high-density freight allow large volumes of units to be mobilised in the shortest possible window |
|
Epidemic isolation facilities |
Rapid forming, independent units, whole-box relocation and reuse |
|
Remote camps / mining accommodation |
Where inland transport is constrained, loading density directly determines logistics cost |
|
Site offices / field accommodation |
At project close-out the whole box relocates to the next site, amortising cost across deployments |
How the foldable system compares
vs. expandable units: Foldable deploys faster and has a simpler cost structure. Expandable units deliver far more area per shipped module - a 20ft expandable reaches 36 m² deployed - and suit family housing, clinics and canteens.
vs. flat pack / modular bolt-together: Foldable has the highest transport efficiency. Flat pack offers greater customisation and combination flexibility for large phased camps.
Foldable trade-offs: Folding hinges and sealing systems raise manufacturing cost, so unit price sits at the higher end of the three systems; internal space is comparatively fixed, with less customisation latitude than bolt-together modules.
Installation, Shipping & Lifting
Shipping condition
Units travel folded as whole boxes - no over-width or over-height condition, so no over-width permit is needed. Corner castings follow ISO marine container positioning and are compatible with standard container chassis.
On-site lifting
A certified spreader beam attached to the designated corner fittings is mandatory. Lifting through wall panels or the roof is prohibited. Confirm shipping condition, lifting points and centre of gravity with the supplier before mobilisation.
Foundation
- Levelled concrete strip, screw piles or adjustable steel supports, selected according to soil conditions and intended service life. Ground bearing capacity, drainage and frost depth must be assessed by a local engineer.
- Risk note: An unlevel or poorly drained base causes frame distortion and door misalignment - the most frequent source of warranty disputes for this product class. Foundations are normally outside the unit supply scope and must be quoted separately.
Shipping compliance
- HS code: 9406900090 (prefabricated buildings)
- ISPM 15 phytosanitary treatment applies where timber components are present
- VGM is the responsibility of the shipper named on the bill of lading and must be submitted before vessel stowage planning
- Export documents: commercial invoice (stating material, specification and function), packing list (per-box weight, dimensions, quantity), customs declaration
Customisation Options
|
Category |
Options |
Impact |
|
Envelope |
Core upgrade (EPS→rock wool→PU), thickness upgrade (50→75→100mm), thicker steel skins |
Determines fire rating, U-value and acoustics; thicker panels reduce units per container |
|
Openings |
Additional or larger doors and windows, thermally broken aluminium, Low-E insulated glazing, toughened glass |
Frames and hardware need protected packing and may reduce loading quantity |
|
Structural |
Heavier steel, Q345 substitution, strengthened stacking nodes, upgraded base frame sections |
Requires reissued structural calculations and may trigger certification review |
|
Fit-out |
Prefabricated bathroom pod, kitchen, timber-effect internal cladding, ceiling, acoustic upgrade |
Sanitary fixtures pack irregularly and raise damage risk |
|
Electrical |
Destination voltage and frequency, distribution board specification, socket standards, solar PV |
Must be locked before order confirmation |
|
Cosmetic |
Facade cladding, colour, branding |
No structural or certification impact; quote separately from structural options |
|
Accessories |
Stairs, canopies, handrails, external steps |
Loose items consuming residual container volume |
FAQ
Q: Do folding hinges loosen or leak after repeated cycles?
Hinges and sealing systems are where cost and failure concentrate in this product class. Specify the folding cycle figure in the contract as either a manufacturer claim or a tested value - and state which it is. Request written confirmation of sealant climate suitability.
Q: Why do loading quantities vary so much between suppliers?
Loading quantity must satisfy three independent limits simultaneously: geometry (do the packages physically fit), mass (is the payload reached before the cube is full), and equipment/route (will the booked container and carrier accept it). Panel thickness, openings, sanitary fixtures, MEP content and protective dunnage all change the answer. Compare the configuration schedule behind the number, not the number itself.
Q: Can units be stacked two high?
Stacking capacity depends on base frame section and node design. Obtain written confirmation from the factory for the intended number of storeys; do not apply a generic value.
Q: What matters for coastal projects?
Corrosion at cut edges and fasteners is a common long-term issue. Coastal and high-humidity sites demand a higher coating specification and more corrosion-resistant fasteners than inland dry sites.
Q: How should quotations be compared fairly?
Compare on landed cost per square metre, not headline unit price. Landed cost includes ocean freight, insurance, port handling, import duty, inland transport, crane hire, foundation works, utility connections and commissioning labour - which together can rival the equipment cost itself.
Hot Tags: 20ft foldable container house, China 20ft foldable container house manufacturers, suppliers, factory


